Copy-Paste Waypoints Across Missions

FlytBase now supports copy-paste of waypoints across missions in the 3D Mission Planner, allowing operators to reuse previously created waypoints including camera actions, gimbal settings, and inspection logic across different missions.

This enables faster mission creation, eliminates repetitive setup work, and allows inspection missions to be assembled from existing waypoint building blocks instead of being recreated from scratch.

Copy-paste waypoints across missions. Select waypoints in one mission and paste them into another while preserving actions and camera configuration.

The Mission Reuse Problem

Building inspection missions requires careful setup:

• Waypoints must be positioned precisely • Gimbal angles and zoom levels need tuning • Oriented Shoot and AI Spot Check actions must be aligned correctly

For Live Mission Recording, the investment is even higher—real flight time is spent framing shots and capturing waypoints one by one.

Previously, once a mission was created, its waypoints were locked to that mission. When inspection scopes changed, operators had limited options:

• Recreate the mission manually • Duplicate a mission and delete unwanted waypoints • Record an entirely new Live Mission Recording session

This became especially inefficient when assets were recorded across multiple missions. Executing those missions required repeated launch-fly-return cycles, wasting battery and time on redundant transit instead of inspection.

Waypoints can now be copied from one mission and pasted into another, turning existing missions into reusable waypoint libraries.

Copy-Paste Waypoints

Waypoints can now be copied from one mission and pasted into another, turning existing missions into reusable waypoint libraries.

Everything associated with a waypoint can be transferred:

• Position and altitude • Gimbal angles and camera zoom • Waypoint actions • Oriented Shoot configuration • AI Spot Check reference images

Selection of multiple waypoints

Waypoints are copied without modifying the source mission, allowing recording missions to remain intact while execution missions are consolidated.

Two Copy Modes

Two copy options are available depending on the use case:

Copy waypoints and actions Preserves full waypoint configuration, including actions, gimbal settings, and camera parameters. Recommended when reusing inspection or Live Mission Recording waypoints.

Copy waypoints only Transfers waypoint positions without actions. Useful when reusing a flight path for a different operational purpose.

Waypoint copy options showing “Copy waypoints only” and “Copy waypoints and actions”.

Copying Waypoints: Step by Step

1. Open the source mission

Open the mission containing the waypoints you want to reuse in the 3D Mission Planner.

2. Enter multi-select mode

Enable waypoint multi-select from the toolbar or press Ctrl/Cmd + M.

3. Select waypoints

• Ctrl/Cmd + Click - select individual waypoints • Shift + Click - select a range • Ctrl/Cmd + A - select all • Escape - clear selection

4. Copy

Click any selected waypoint and choose either:

• Copy waypoints only, or • Copy waypoints and actions

5. Switch to the destination mission

Open an existing mission or create a new one in a separate tab. Select the waypoint after which the copied waypoints should be inserted.

6. Import

Click Import Waypoints in the toolbar and select Copied Waypoints.

The copied waypoints are inserted immediately after the selected waypoint, maintaining their original order. All actions and camera configurations are preserved if included during copy.

Note: If the source and destination missions use incompatible hardware, validation errors will be raised.

Why This Changes Mission Planning

Consolidating Live Mission Recording Sessions

Live Mission Recording is time-intensive to create but fast to execute. When recordings are split across multiple missions, execution becomes inefficient due to repeated launch and transit cycles.

Copy-paste allows operators to:

• Combine waypoints from multiple recording missions • Execute all inspections in a single flight • Reduce redundant dock-to-site transit

Recording missions remain untouched and reusable for future workflows.

Mix-and-Match Asset Coverage

Different inspection scenarios require different asset combinations:

• Routine inspections • Post-event assessments • Targeted follow-ups

Instead of rebuilding missions, operators can now pull the required waypoints into a new mission. Missions become modular asset libraries rather than fixed flight plans.

Mission Editing Improvements

Copy-paste is supported by several mission editing enhancements.

Drag-and-Drop Waypoint Reordering

Waypoints can be reordered directly in the waypoint list:

• Drag waypoints to reposition them • Use Alt/Opt + Space, then Arrow Up/Down for keyboard reordering

The flight path updates instantly in the 3D map.

Reorder waypoints directly in the waypoint list with the flight path updating in real time.

Insert Waypoints in Existing Sequences

New waypoints can be added before or after any existing waypoint, not just appended at the end. This simplifies mid-mission edits.

Multi-Select and Bulk Delete

Multiple waypoints can be selected and deleted in a single action, making mission cleanup faster and more precise.

Multi-select multiple waypoints and delete them in a single action.

Waypoint Errors and Suggestions

The 3D Mission Planner now validates mission configuration and surfaces issues in a Suggestions and Errors panel.

Examples include:

• Stop recording without a corresponding start action • Invalid or conflicting waypoint configurations

Suggestions and errors highlighted during mission planning to catch configuration issues early.

Errors are flagged during planning, before mission execution.

---

KML Import

Line KML files can now be imported during mission creation.

• KML vertices are converted into waypoints • Imported waypoints can be edited, reordered, and enhanced with actions

This is useful for teams maintaining routes or asset locations in GIS tools or Google Earth.

Import line KML files to convert existing routes into waypoint missions.

Notes: • Line KMLs only • Polygon KMLs are not supported • No interpolation between vertices

---

Keyboard Controls

A comprehensive keyboard control system is available for waypoint management.

Keyboard controls are disabled by default and can be enabled from the bottom toolbar. A full keymap reference is accessible via the info panel.

Enable or disable keyboard controls from the mission planner toolbar.

View the full keyboard control reference for waypoint navigation and editing.

Supported control areas

Movement

• WASD for horizontal movement

• Z/C for altitude adjustment

Navigation

• Tab - cycle waypoints

• Arrow keys - navigate waypoints and actions

• Alt/Opt + Space - reorder mode

Waypoint Actions

• Single-key shortcuts for common actions such as photo capture, video recording, hover, yaw, and zoom

Multi-Select

• Ctrl/Cmd + M - toggle multi-select

• Ctrl/Cmd + Click, Shift + Click - selection

• Ctrl/Cmd + A - select all

• Escape - clear selection

Keyboard controls significantly reduce editing time for complex missions with many waypoints.

Hardware Compatibility

All features in this release are supported across all FlytBase-supported devices.

The 3D Mission Planner’s linear mission capabilities work with any hardware configured in your FlytBase deployment.